Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Blog Article
This post which follows involving How to Install a Bathtub Yourself is particularly interesting. Read it yourself and figure out what you think of it.
Mounting a tub isn't precisely rocket science, but it does call for strong plumbing, woodworking, as well as sometimes, tiling skills. Changing an old bathtub with a new one is likewise a reasonably hard task. If the old bathtub is conveniently accessible, the task can relocate easily; if you need to open a wall to remove the old bathtub as well as place the brand-new tub, the task is much harder. In either case, the task is within a home handyman's skills, although you will certainly need an assistant to vacate the old bathtub and also embeded in the new one. Ensure you have qualified yourself for the job and also are comfortable trying it. As opposed to employing a specialist to take over a halfway-completed task, it is far better to consider using one prior to you start. Possibilities are you might require an expert plumber to make tube connections.
This post will certainly help you install a brand-new tub in your bathroom if you have currently acquired a brand-new bathtub and also do not need to alter the arrangement of your previous supply of water pipelines.
Your tools and also product list need to comprise the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your setup, after that the first thing you ought to do is disconnect the water supply. After doing so, switch on the faucets to drain pipes any type of water continuing to be in the system. The procedure of removing the existing taps can be quite problematic as a result of the restricted gain access to that is commonly the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipes have actually been removed, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning throughout this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any old securing compound.
Before going on to fit the new faucets, compare the pipe links on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic adapter to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end provides a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly call for lowering couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the faucet in the mounting opening in the bath/basin ensuring that the washing machines are in area between the tap as well as the sink. Secure the faucet in position with the producer offered backnut. Once the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical faucet adapters. The former type needs to be linked to the faucet ends first, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Mounting the Tub
Using both wood boards under its feet, put the bath tub in the needed position. The wooden boards are helpful in equally spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four little points.
The next objective is to make certain that the bath tub is leveled all round. This can be accomplished by checking the spirit level as well as changing the feet on the bathtub up until the spirit level checks out degree.
To install taps, fit the bottom of the outermost versatile tap port to the proper supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the supply of water as well as inspect all joints as well as new pipework for leaks and tighten them if required. Fill the bath tub as well as also examine the overflow electrical outlet as well as the normal electrical outlet for leakages.
Lastly, repair the bathroom paneling as explained in the producer's user's manual. Tiling as well as securing around the bathtub must wait up until the bathtub has been made use of a minimum of once as this will certainly resolve it into its last position.
Planning for the Setup
Firstly, the supporting structure supplied with the bath needs to be fitted (if needed) according to the supplier's directions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to make sure that if the faucet features a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is likewise sensible to fit a sustaining plate under the faucets device to prevent strain on the bath tub.
Fit the versatile faucet ports to the bottom of the two faucets using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you utilize all of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to currently be ready to be fitted in its final position.
Tiling Around the Bathtub
In the location where the bathroom satisfies the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can move sufficient to crack an inflexible seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, bring about issues with dampness and also possible leakages to the ceiling below.
You can select from a variety of coloured sealants to assimilate your components and installations. They are marketed in tubes and cartridges, and also are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly load the bathtub with water before sealing, to allow for the motion experienced when the tub is in use. The sealant can fracture rather very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily readily available on the marketplace. It is a good idea to fit the floor tiles making use of waterproof or waterproof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a devoted person who reads on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I thought sharing that piece of content was a great idea. Do you know about anybody else who is fascinated about the subject? Be sure share it. Thanks for your time. Visit us again soon.
Visit Page Report this page